Spanjaard Silicone Paste consists of a silicone oil, thickened with an inorganic gelling agent to form a 'non-melting' stable paste. In addition to its usefulness as a lubricant it is highly resistant to water, has excellent insulating properties and had many applications as a release agent.
Application
1) Lubricant: to lubricate parts and bearings under low speeds and light loads. Lubricates and does not affect rubbers and plastics e.g.
- Refrigerator and card door seals.
- Swimming pool rubbers and seals.
- Plastic gears and mechanisms.
- Electric cables drawn through conduit.
- Laboratory glass joints.
- Rubber components and cylinder rolls in train air brake applications.
- NSF registered (H1 and H2 status).
- Meets requirements of British Mil. Spec. XG-250.
* Not suitable for High Impact Polystyrene (HIPS).
2) Water and Corrosion Resistance: Seals electrical equipment against the ingress of moisture, and protects metal parts against corrosion e.g.
- Seals outdoor electrical fittings.
- Protects chrome plating.
- Seals screw threads and automobile battery terminals.
3) Insulating Compound: Spanjaard Silicone Paste is non-conductive and prevents electrical leakage and short circuiting e.g.
- Sealing and potting of electrical and electronic components.
- Prevents tracking on insulators.
- Protects automobile ignition systems.
- Prevents ionisation and sparking on electrical equipment.
4) Releasing Agent: Acts as a releasing agent in the rubber and plastics industries as well as many others e.g.
- Can be used as a release agent for polystyrene, PVC, phenolic and other resins.
- Prevents binding of components when coiled insulation varnish is cured at high temperatures.
- Acts as a mould release for rubber as well as a lubricant and preservative.
- Prevents resin build up when epoxy and other glues are used.
- Prevents icing up in deep freezers & on ski bindings.
Application Instruction
Apply with brush, finger or grease gun.
Typical Properties
TYPICAL PROPERTIES |
SPANJAARD SILICONE PASTE |
Consistency – NLGI grade |
3 |
Worked penetration, 25°C, 1/10mm |
220 |
Colour |
White translucent |
Thickener |
Silica |
Drop point, °C |
None |
Evaporation loss 30hrs @ 175°C, % |
1.0 |
Dynamic rust test |
<1 |
Copper corrosion – 24hr/100°C |
Pass |
Oil bleed 30h @ 175°C, % |
0.2 |
Water wash out @ 93°C, % |
1.0 |
Timken OK load, kg |
1 |
Oxidation resistance, D942, % |
1.0 |
Dielectric strength, kV/mm |
15 |
Useful temperature range, °C |
-40 to 200 |
|
|
SILICONE OIL PROPERTIES |
|
Oil viscosity csT, 40°C |
750 |
Flash point, °C |
>250 |
Contact our sales consultant in area:
Malaysia, Selangor (Klang, Puchong, Shah Alam, Subang), Kuala Lumpur (Sungai Buloh), Negeri Sembilan (Seremban), Melaka, Johor (Johor Bharu, Muar, Batu Pahat), Pahang (Temerloh, Kuantan), Kelantan (Kota Bahru), Terengganu (Kuala Terengganu), Perak (Ipoh), Kedah (Sungai Petani), Perlis, Penang (Bukit Mertajam, Butterworth, Seberang Prai), Sabah (Kota Kinabalu), Sarawak (Kuching), WP Putrajaya, WP Labuan, Indonesia, Singapore, Thailand, Philippines, Vietnam, Laos, Myanmar, Cambodia, Brunei at sales@davor.com.my.